Hanashield Elastomeric Sealer

$17.00 – $100.00

Hanashield Elastomeric Sealer is a water-proofing sealant made of acrylic elastomer that prevents further water penetration into the substrate.

  • Choose Your Color

Request Quote

    Whatsapp Enquiry

    Wishlist

    SKU: N/A Category: Tags: ,

    Weight N/A
    Features

    Environmental Friendly, Weather Resistance
    Paints

    Primers, Sealers & Undercoats
    Size

    1 Litre, 5 Litres, 18 Litres

    Description

    Hanashield Elastomeric Sealer is a premium waterproofing and sealer membrane based on a 100% acrylic elastomeric polymer system with excellent flexibility, adhesion, and protection properties to protect concrete and masonry surfaces. It is a highly flexible coating to cover hairline cracks and has excellent adhesion to seal the pores on the concrete to prevent further water penetration into the substrate. It is a green and eco-friendly product without any harmful substances.

    Features

    • Good Water Resistance.
    • Easy to use spray, brush, roller
    • Cracks bridging and excellent adhesion.
    • Alkaline resistance and efflorescence resistance.
    • Flexible and durable coating
    • Environmental friendly product and free from harmful chemicals such APEO & formaldehyde.

    Typical Uses

    Premium elastomeric sealer and waterproofing system for all masonry surfaces such as brickwork, concrete, plaster, and textured surfaces. Suitable for use as eco-friendly concrete wall sealer and waterproofing roofing.

    Physical Data

    Color : As specified
    Volume Solid : 50 +/- 2%
    Finish : Matt finish
    Solid Content : 60 +/- 2%
    VOC(as supplied) : Near zero
    Shelf Life @250C / indoor : 24 months

     

    Typical Thickness: 60 ~  100µ dried film.

    Drying Time(at Dry Film Thickness 60µ) Temperature 100C 200C 300C
    Surface Dry 3 hrs 2 hrs 1 hrs
    Hard Dry 6 hrs 4 hrs 3 hrs
    Painting interval: Minimum 5 hrs 3 hrs 2 hrs
    Max. (self) – – –
    Pot LIfe – – –
    Theoretical coverage
    (at DFT 60- 100µ)    		 0.120~0.20L/m2 ; 8.3 ~ 5.0 m2/L
    Service temperature -20 to 120 0C (dry)

    Application Data

    Mixing ratio: not applicable

    Application Method: airless spray, roller, brush

    Mixing Procedure : Hand stir for at least two minutes or until homogeneous.
    Drying schedule : Drying by water evaporation. Higher film thickness, insufficient ventilation, or lower temperature will require longer drying time.

    This product requires the substrate temperature to be above the dew point ( + 3~5 0 C).

    Application Procedure

    Mix properly the paint before use.

    1. Flush equipment with water before use.
    2. Mix the paint thoroughly until homogeneous.
    3. Thin with water only if necessary for workability.
    4. When applying by conventional spray, use adequate air pressure and volume for proper atomization.
    5. Apply a wet coat in even parallel passes, and overlap 50% to avoid holidays and pinholes.
    6. Excessive thickness can prolong drying and sagging.
    7. Clean up all equipment with water immediately after use.
    8. Keep containers tightly close and store them in a proper storage area.

    Condition of Application

    Use a brush or roller with a 1/8″ nap. Apply at a sufficient thickness and avoid repeating rolling to have good leveling.

    Temperature : Min 5 0 C ; Max 50 0 C
    Humidity : Maximum 85 % R.H.
    For Airless spray:-
    Tip Size : Graco 615, 715 or equivalent
    Paint Output pressure : 10.7 – 13.8 MPa (g)
    Viscosity : 1.5 ~ 2.0 Pa.s
    Thinning : 0 – 10 % by volume
    Recommended Painting system : 1)Use as a sealer; 1-2 coats depending on concrete condition)

    2)Use as patching material to cover hairline cracks: 2 -3 coats depending on substrate condition without thinning

    Surface Preparation

    General :
    Surfaces must be clean and dry, and all contaminants like dirt, dust, and oil must be removed by appropriate methods to ensure good adhesion.

     
    Moisture
    Ensure the surface is dry before painting. Moisture must be < 10% before application

     
    Concrete Structure
    Concrete must be cured for at least 30 days prior to coating and must be free from moisture as much as possible. The surface must be cleaned, and free from any contaminant, laitance, and loose film. Broom cleaning, vacuum cleaning, air blast cleaning, and steam and water cleaning are suitable as outlined in ASTM D4258.

     
    Contaminants
    Remove dust and foreign matter by cleaning with a damp cloth. Remove oil or grease using mild detergent and allow the surface to dry.

     

    Safety Precaution & Clean-Up

     

    Safety :

    		 Read and follow the material safety data sheet (MSDS) before use. Employ normal safety precautions. Put on necessary personal protection equipment when handling and using this product.
     Ventilation : when working in a confined workplace, thorough air ventilation must be used during and after application until the coating is cured. The ventilation system should be effective to prevent solvent vapor concentration from reaching a lower explosion limit for the product and to ensure exposure limit to the personnel is below the permissible exposure limit.
    Caution : All electrical equipment and installations should be made and properly grounded. In areas where explosion hazards exist, workmen should be used non-ferrous tools and conductive and non-sparkling shoes.
    Clean-up : Use Hana Paint polyurethane thinner (Hana Thinner U)  or hydrocarbon solvent for cleaning. Observe safety precautions when using the solvents. In case of spillage, absorb and dispose of the material and used container according to local required regulations or through a licensed waste collector.

    Disclaimer & Limited Warranty

    Disclaimer

    Data, specifications, directions, and recommendations given in this data sheet represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness, or appropriateness under the actual conditions of any intended use is not guaranteed and must be determined by the user. The products are delivered and any technical assistance is given subject to our GENERAL CONDITIONS OF SALE, DELIVERY, AND SERVICE and, unless otherwise expressly agreed in writing, manufacturer and seller assume no liability in excess of that stated therein for results obtained, injury, direct or consequential damage incurred from the use as recommended above or otherwise.

    Limited Warranty

    Whilst we endeavor to ensure that all advice we give about this product is correct and manufactured according to the standard quality control system, however, we have no control over either the quality or condition of the substrate or many other factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage arising out of the use of this product.

    Need Help?

    Send Us An Email

    Contact us at [email protected] or call us at +65 6898 2314 for questions related to these products or send us a form via the contact form below.

      Reviews

      There are no reviews yet.

      Only logged in customers who have purchased this product may leave a review.

      Related products

      Quick View

      HanaShield

      Hanashield Interior

      $18.00 – $160.00

      Hanashield Interior is a high-performance, eco-friendly and odorless all-in-one coating that is resistant to fungus and mold growth.

      Select options
      Quick View

      HanaShield

      Hanashield IR HR Heat Reflective Coating

      $25.00 – $270.00

      Hanashield IR HR Heat Reflective Coating is an infrared heat reflective coating that helps keep your home cool this summer.

      Select options
      Quick View

      HanaShield

      Hanashield Penetrating Sealer

      $17.00 – $39.00

      Hanashield Penetrating Sealer is a sealer that penetrates and bonds with chalky and porous substrates, helping to strengthen and improve the adhesion of subsequent plaster, skim coat, or coating.

      Request Quote

        Quick View

        HanaShield

        Hanashield Kurin Hygienic coating

        $19.00 – $199.00

        Hanashield Kurin is a synthetic emulsion paint that provides superior anti-bacterial protection, is odorless, has excellent quality, and eco-friendly.

        Select options
        Quick View

        HanaShield

        Hanashield High Gloss Finish

        $19.00 – $180.00

        Hanashield High Gloss Finish is a high gloss waterborne paint that is easy to use and has excellent gloss and weathering properties.

        Select options
        Quick View

        HanaShield

        Hanashield Fungicidal Wash

        $10.00 – $35.00

        HanaShield Fungicidal Wash is a water-based chemical wash that kills fungus and algae on all surfaces without affecting paint coats.

        Select options
        Quick View

        HanaShield

        Hanashield Exterior

        $20.00 – $240.00

        Hanashield Exterior Coating is a high-performance, multi-purpose elastomeric paint coating that protects concrete, wood, and metal finishes.

        Select options

        Shop by Product Type

        Cool Galv

        Corrosion Painting

        View more

        Hanashield

        Exterior & Interior Painting

        View more

        Stabilis

        Metal Painting

        View more

        Sign up for our newsletter

        Keep up with the latest trends, exclusive offers and new product launches by subscribing to our newsletter. Get 5% off on your next purchase just for signing in!

          tel: +65 6898 2314

          Available 9:00 - 18:00

          [email protected]

          Drop us a mail

          Contact Us shop now
          This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.
          More info Accept