Weight | N/A |
---|---|
Features | Bacterial & Fungue Resistance, Environmental Friendly |
Paints | Surface Treatment |
Size | 1 Litre, 2 Litres, 400 ml, 5 Litres |
Hanashield Fungicidal Wash
$10.00 – $35.00
HanaShield Fungicidal Wash is a water-based chemical wash that kills fungus and algae on all surfaces without affecting paint coats.
- Additional information
- Description
- Features
- Typical Uses
- Physical Data
- Application Data
- Application Procedure
- Surface Preparation
- Safety Precaution & Clean-Up
- Disclaimer & Limited Warranty
- Need Help?
- Reviews (0)
Description
Features
- Ready to use in a trigger spray bottle.
- Suitable for all surfaces contaminated with mould, fungi, algae or lichen.
- Kills a wide spectrum of mould, fungus and algae
- Suitable for interior and exterior surfaces
- Resistant to fungus and mould growth
- Environmental friendly product and 100% water base.
Typical Uses
High-grade anti-fungus and algae wash for all surfaces for both interior and exterior applications. Suitable for brush application to new or painted interior or exterior wood or masonry surfaces contaminated with mold, fungi, algae, or lichen.
Physical Data
Color | : | Clear liquid |
VOC(as supplied) | : | zero |
Shelf Life @250C / indoor | : | 24 months |
Drying Time | : | 2 – 4 hours
Leave on the surface for 24 hours and then rinse with clean water to remove dead growth/residue. |
Theoretical coverage | : | ~ 25 m2 /L |
Application Data
Application Method: by brush
Mixing Procedure : | Hand stir for at least two minutes or until homogeneous. |
Drying schedule : | Drying by water evaporation. Leave for 24 hours and then thoroughly rinse and scrub with clean water to remove residue and dead growth. |
Application Procedure
Mix properly the chemical before use.
- Apply the solution with a brush.
- Leave for 24 hours and then thoroughly rinse and scrub with clean water to remove residue and dead growth.
- Repeat the process if necessary.
- Do not apply in wet weather.
- Badly affected areas may require the use of high-pressure water jetting to remove all organic growth completely
- When the surface is fully dry, then apply the subsequent coating
- Clean up all equipment with water immediately after use.
- Keep containers tightly close and store them in a proper storage area.
Surface Preparation
General : |
Surfaces must be clean and dry, and all contaminants like dirt, dust, and oil must be removed by appropriate methods to ensure good adhesion.
Badly affected areas or if lichen is present may require high-pressure water jetting to remove all organic growth |
Safety Precaution & Clean-Up
Safety : |
Read and follow the material safety data sheet (MSDS) before use. Employ normal safety precautions. Put on necessary personal protection equipment when handling and using this product. |
Ventilation : | when working in a confined workplace, thorough air ventilation must be used during and after application until the coating is cured. The ventilation system should be effective to prevent solvent vapor concentration from reaching a lower explosion limit for the product and to ensure exposure limit to the personnel is below the permissible exposure limit. |
Caution : | All electrical equipment and installations should be made and properly grounded. In areas where explosion hazards exist, workmen should be used non-ferrous tools and conductive and non-sparkling shoes. |
Clean-up : | Use Hana Paint polyurethane thinner (Hana Thinner U) or hydrocarbon solvent for cleaning. Observe safety precautions when using the solvents. In case of spillage, absorb and dispose of the material and used container according to local required regulations or through a licensed waste collector. |
Disclaimer & Limited Warranty
Disclaimer
Data, specifications, directions, and recommendations given in this data sheet represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness, or appropriateness under the actual conditions of any intended use is not guaranteed and must be determined by the user. The products are delivered and any technical assistance is given subject to our GENERAL CONDITIONS OF SALE, DELIVERY, AND SERVICE and, unless otherwise expressly agreed in writing, manufacturer and seller assume no liability in excess of that stated therein for results obtained, injury, direct or consequential damage incurred from the use as recommended above or otherwise.
Limited Warranty
Whilst we endeavor to ensure that all advice we give about this product is correct and manufactured according to the standard quality control system, however, we have no control over either the quality or condition of the substrate or many other factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage arising out of the use of this product.
Need Help?
Send Us An Email
Contact us at [email protected] or call us at +65 6898 2314 for questions related to these products or send us a form via the contact form below.
Only logged in customers who have purchased this product may leave a review.
Related products
HanaShield
Hanashield Exterior Coating is a high-performance, multi-purpose elastomeric paint coating that protects concrete, wood, and metal finishes.
HanaShield
Hanashield Penetrating Sealer is a sealer that penetrates and bonds with chalky and porous substrates, helping to strengthen and improve the adhesion of subsequent plaster, skim coat, or coating.
Request QuoteHanaShield
Hanashield Interior is a high-performance, eco-friendly and odorless all-in-one coating that is resistant to fungus and mold growth.
HanaShield
Hanashield IR HR Heat Reflective Coating is an infrared heat reflective coating that helps keep your home cool this summer.
HanaShield
Hanashield High Gloss Finish is a high gloss waterborne paint that is easy to use and has excellent gloss and weathering properties.
HanaShield
Hanashield Elastomeric Sealer is a water-proofing sealant made of acrylic elastomer that prevents further water penetration into the substrate.
HanaShield
Hanashield Kurin is a synthetic emulsion paint that provides superior anti-bacterial protection, is odorless, has excellent quality, and eco-friendly.
Sign up for our newsletter
Keep up with the latest trends, exclusive offers and new product launches by subscribing to our newsletter. Get 5% off on your next purchase just for signing in!
Reviews
There are no reviews yet.